zcM3000 Parts List
zcM3000 Parts List
Part # | Description |
ZCM3000P101 | bottom plate |
ZCM3000P102(110) | 120V transformer |
ZCM3000P102(220) | 230V transformer |
ZCM3000P103 | condenser |
ZCM3000P103-1 | screw (4 X 10) |
ZCM3000P103-2 | u nut |
ZCM3000P104 | fuse holder (w/connector) |
ZCM3000P104-1 | rubber for leg |
ZCM3000P104-2 | rivet |
ZCM3000P104-3 | washer 3mm |
ZCM3000P105(110) | cord (w/connector) (100V,120V) |
ZCM3000P105(220) | cord (w/connector) (220V) |
ZCM3000P105-1 | screw for earth |
ZCM3000P105-2 | ground label |
ZCM3000P201 | body cover right |
ZCM3000P202 | key top |
ZCM3000P203 | ornament plate |
ZCM3000P204 | mainboard |
ZCM3000P205 | key board |
ZCM3000P206 | board attachment plate 1 |
ZCM3000P207 | board attachment plate 2 |
ZCM3000P208 | power switch |
ZCM3000P208-1 | screw for main board |
ZCM3000P208-2 | screw for board attachment |
ZCM3000P208-4 | convex |
ZCM3000P209 | board cover left |
ZCM3000P209-1 | screw for body cover |
ZCM3000P301 | right board |
ZCM3000P302 | left board |
ZCM3000P303 | latch pin |
ZCM3000P304 | idle pin |
ZCM3000P305 | reel spring right |
ZCM3000P306 | reel spring left |
ZCM3000P306-1 | screw for reel spring |
ZCM3000P306-2 | u nut |
ZCM3000P307 | bearing |
ZCM3000P308 | idle gear 1 |
ZCM3000P309 | idle gear 2 |
ZCM3000P310 | idle gear 3 |
ZCM3000P311 | cam gear |
ZCM3000P312 | chopper 1 |
ZCM3000P313 | clutch |
ZCM3000P314 | cam shaft |
ZCM3000P315 | chopper 2 |
ZCM3000P316 | cam |
ZCM3000P317 | bearing |
ZCM3000P317-1 | screw for cam |
ZCM3000P317-2 | nut for cam |
ZCM3000P317-3 | spring pin |
ZCM3000P318 | clutch shaft |
ZCM3000P319 | shaft |
ZCM3000P320-1 | motor (100V,230V) |
ZCM3000P320-2 | motor (230V) |
ZCM3000P321 | motor gear |
ZCM3000P322 | cut sensor (w/connector) |
ZCM3000P323 | feed sensor (w/connector) |
ZCM3000P324 | connector 1 (for clutch) |
ZCM3000P325 | middle board |
ZCM3000P326 | clutch attachment board |
ZCM3000P327 | sensor stand |
ZCM3000P328 | actuator 1 |
ZCM3000P329 | actuator 2 |
ZCM3000P329-1 | screw for motor |
ZCM3000P329-10 | screw (4 X 8) for ground |
ZCM3000P329-11 | e ring |
ZCM3000P329-12 | nylon clip (for connector) |
ZCM3000P329-2 | screw for motor |
ZCM3000P329-3 | screw for shaft |
ZCM3000P329-4 | screw for cut sensor |
ZCM3000P329-5 | nut (M3) |
ZCM3000P329-6 | screw for micro switch |
ZCM3000P329-7 | nut (M2.3) |
ZCM3000P329-8 | screw (2.3 X 12) |
ZCM3000P329-9 | screw (3 X 6) for clutch attachment |
ZCM3000P330 | roller guide plate |
ZCM3000P331 | gear cover |
ZCM3000P332 | motor line fixer |
ZCM3000P401 | front board |
ZCM3000P402 | tape stopper |
ZCM3000P403 | tape guide |
ZCM3000P403-1 | screw for tape stopper |
ZCM3000P403-2 | rivet for tape guide |
ZCM3000P404 | cutter holder |
ZCM3000P405 | slider |
ZCM3000P406 | cutter spring 1 |
ZCM3000P407 | cutter spring 2 |
ZCM3000P408-9 | cutter 1 |
ZCM3000P410 | cutter shaft |
ZCM3000P411 | front latch |
ZCM3000P412 | front latch knob |
ZCM3000P413 | latch spring |
ZCM3000P413-1 | screw for slider |
ZCM3000P413-2 | screw for cutter 1 & 2 |
ZCM3000P413-3 | u nut for cutter 2 |
ZCM3000P413-4 | e ring for cutter shaft |
ZCM3000P414 | silicon oil (0.1 cc) |
ZCM3000P415 | roller cover |
ZCM3000P416 | roller cover knob |
ZCM3000P417 | roller cover latch |
ZCM3000P418 | latch spring 2 |
ZCM3000P419 | latch shaft |
ZCM3000P420 | roller cover attachment |
ZCM3000P421-22 | pressure shaft |
ZCM3000P423 | pressure ring |
ZCM3000P424 | pressure plate |
ZCM3000P425 | press roller attachment |
ZCM3000P426 | press roller |
ZCM3000P427 | press roller shaft |
ZCM3000P428 | press roller spring |
ZCM3000P428-1 | nut for pressure shaft |
ZCM3000P428-2 | e ring for pressure & roller shaft |
ZCM3000P428-3 | screw for roller cover |
ZCM3000P429 | shaft for front board |
ZCM3000P430 | push |
ZCM3000P430-1 | e ring for front board shaft |
ZCM3000P431 | cap |
ZCM3000P432 | front cover |
ZCM3000P433 | sensor cover |
ZCM3000P434 | anti sticking cover 1 |
ZCM3000P435 | anti sticking cover 2 |
ZCM3000P436 | micro sensor |
ZCM3000P437 | connector 2 for sensor |
ZCM3000P437-1 | screw for front cover |
ZCM3000P438 | cutter guide spring |
ZCM3000P439 | pressure spring |
ZCM3000P532 | micro switch unit 1 (w/connector) |
ZCM3000P533 | micro switch |
ZCM3000P560 | roller unit |
ZCM3000P601 | roller fastener |
ZCM3000P602 | roller shaft |
ZCM3000P603 | feed roller ring |
ZCM3000P604 | separating roller ring |
ZCM3000P605 | spacer 1 |
ZCM3000P606 | spacer 2 |
ZCM3000P607 | idle gear3/main gear |
ZCM3000P607 | main gear |
ZCM3000P608 | separating roller gear |
ZCM3000P608-1 | e ring |
ZCM3000P608-2 | e ring |
ZCM3000P609 | separating roller gear |
ZCM3000P610 | spacer 3 |
ZCM3000P611 | spacer 4 |
ZCM3000P612 | spacer 5 |
ZCM3000P701-2 | reel |
ZCM3000P807 | silicon oil |
ZCM3000P809 | ground |
ZCM3000P906 | manual |
ZCM3000P907 | tape set lable |
ZCM3000P912 | packing |
ZCM3000P914 | voltage label |
ZCM3000P919 | caution label |
ZCM3000P942 | air cap |
ZCM3000P945 | lot label |
zcM2200 Parts List
zcM2200 Parts List
zcM2200-Specific Parts
Part # | Description |
ZCM2200P101 | body cover |
ZCM2200P550 | PCB |
zcM Series Parts
Part # |
Part Name |
Note |
zcM1000P101 |
Body cover |
Standard Part |
zcM1000P102 |
Panel cover |
Standard Part |
zcM1000P105 |
LED cover |
Standard Part |
zcM1000P106 |
Pressure Knob |
Standard Part |
zcM1000P107B |
Core holder |
Standard Part (1" / 35mm / 3") |
zcM1000P111 |
Transformer 117V |
Standard Part (on 117 V Machines) |
zcM1000P112 |
Transformer 230V(CE) |
Standard Part (on 230 V Machines) |
zcM1000P113 |
Screw (4* 8) |
Standard Part (To hold transformer on base) |
zcM1000P114 |
Nut with washer |
Standard Part (4mm) |
zcM1000P115 |
Base |
Standard Part |
zcM1000P116 |
Rubber feet |
Standard Part |
zcM1000P118 |
Power switch |
Standard Part |
zcM1000P120 |
Fuse (1A) |
Standard Part |
zcM1000P121 |
Fuse holder |
Standard Part |
zcM1000P124 |
Center frame |
Standard Part |
zcM1000P136 |
Separating roller unit |
Standard Part (Used with P138) |
zcM1000P138 |
Separating roller ring |
Standard Part |
zcM1000P141 |
Roller shaft |
Standard Part |
zcM1000P142 |
Screw (3*20) |
Standard Part (To Mount to P136) |
zcM1000P146 |
Bearing |
Standard Part |
zcM1000P150 |
Screw (3*25) |
Standard Part (To Mount feed roller) |
zcM1000P154PP5 |
Pressure roller 5T |
Standard Part (5 teeth for less pressure) |
zcM1000P155 |
Pressure roller collar |
Standard Part |
zcM1000P161 |
Cutter holder spring |
Standard Part |
zcM1000P164 |
Pressure roller spring |
Standard Part |
zcM1000P178 |
Earth spring |
Standard Part |
zcM1000P182 |
Flat rivet |
Standard Part |
zcM1000P187 |
Cutter motor (Yellow & Blue line) |
Standard Part |
zcM1000P200-1 |
Connector 4 (3 pins) |
Standard Part |
zcM1000P204 |
Pinion gear |
Standard Part |
zcM1000P206S |
Power cord (For 117V) |
Standard Part (USA, Plug type B) |
zcM1000P206-2 |
Power cord (For 230V) |
Standard Part (Schuko/EU, Plug type F) |
zcM1000P215 |
Sensor unit cover |
Standard Part |
zcM1000P228 |
Screw (3*8) |
Standard Part (To mount front holder) |
zcM1000P229 |
Screw (3*14) |
Standard Part (To mount control panel) |
zcM1000P230 |
Screw (2.6*3) |
Standard Part (To mount motor, Gold color) |
zcM1000P231 |
Screw (3*10A) |
Standard Part (To mount cutter gear cover) |
zcM1000P232 |
Screw (3*5) |
Standard Part (To mount cutter spring) |
zcM1000P233 |
Screw (3*8) |
Standard Part (To mount body) |
zcM1000P234 |
Screw (3*8) |
Standard Part (To ground earth) |
zcM1000P237 |
Screw (4*6) |
Standard Part (To mount gear unit) |
zcM1000P245 |
Advance / Cut button |
Standard Part |
zcM1000P246 |
"cm" Button |
Standard Part |
zcM1000P247 |
"mm" Button |
Standard Part |
zcM1000P248 |
"Cut" Button |
Standard Part |
zcM1000P249 |
"Advance" Button |
Standard Part |
zcM1000P250 |
"20" Button reset |
Standard Part |
zcM1000P251 |
"Reverse" Button |
Standard Part |
zcM1000P254/5 |
Blade set (Upper & Lower) |
Standard Part (Special coated blades) |
Standard Part (Special coated blades) |
||
zcM1000P256 |
Top Blade Holder |
Standard Part |
zcM1000P257PP |
Blade spring with comb |
Standard Part |
zcM1000P258 |
Blade liner (Right) |
Standard Part |
zcM1000P259 |
Blade liner (Left) |
Standard Part |
zcM1000P289 |
Silicone oil |
Included with all models |
zcM1000P312 |
Feed roller 2 |
Standard Part |
zcM1000P403 |
Flat gear 15 |
Standard Part |
zcM1000P404 |
Flat gear 16 |
Standard Part |
zcM1000P406 |
Flat gear shaft 14 |
Standard Part |
zcM1000P407 |
Flat gear shaft 13 |
Standard Part |
zcM1000P408 |
Collar 2 |
Standard Part |
zcM1000P418 |
Gear unit |
Standard Part |
zcM1000P421 |
Flat Gear 11 |
Standard Part |
zcM1000P422 |
Flat Gear 12 |
Standard Part |
zcM1000P423 |
Flat Gear 13 |
Standard Part |
zcM1000P424 |
Flat Gear 14 |
Standard Part |
zcM1000P427 |
Feed roller gear 3 |
Standard Part |
zcM1000P428 |
Screw (4*8) |
Standard Part (to mount gear cover) |
zcM1000P430 |
Separating roller gear |
Standard Part |
zcM1000P431 |
Cutter gear 2 unit |
Standard Part |
zcM1000P433 |
Cutter part gear cover 2 unit |
Standard Part |
zcM1000P435 |
Feed motor (Red & Brown line) |
Standard Part |
zcM1000P501 |
Side frame (Left) |
Standard Part |
zcM1000P502 |
Side frame (Right) |
Standard Part |
zcM1000P503 |
Separating roller holder |
Standard Part |
zcM1000P504 |
PCB |
Standard Part |
zcM1000P507S |
Cutter holder |
Standard Part (Plastic Frame Only with Front Holes) |
zcM1000P508S |
Cutter holder unit 2 |
Standard Part (Plastic frame + blades with front holes) |
zcM1000P517 |
Roller pressure unit 2 |
Standard Part |
zcM1000P518 |
Front holder unit 3 |
Standard Part (frame + motor) |
zcM1000P519 |
Front holder 3 |
Standard Part (Plastic frame only) |
zcM1000P520 |
Cut lever press 2 |
Standard Part |
zcM1000P521 |
Cut lever liner 2 |
Standard Part |
zcM1000P522 |
Cut lever collar |
Standard Part |
zcM1000P523 |
Cut lever unit 2 |
Standard Part |
zcM1000P524 |
Open spring |
Standard Part |
zcM1000P525 |
Open knob |
Standard Part |
zcM1000P526 |
Open set |
Standard Part |
zcM1000P528 |
Pinion gear unit 2 |
Standard Part |
zcM1000P533 |
Separating roller holder unit |
Standard Part (with P138 roller rings) |
zcM1000P550S |
Auto feed cutter unit |
Standard Part (with 3 flat pin connector) Complete Cutting Head |
zcM1000P555 |
Sensor cover |
(Plastic frame only) |
zcM1000P560-1 |
Sensor unit |
Standard Part (with 3 flat pin connector, frame + sensor) |
zcM1000P680 |
Safety guard (With 4 screws) |
Standard Accessory for 117V, Installed on 230V machines (Need P507-S) |
zcM1000P901 |
Stopper |
Standard Part (to secure cutting head) |
zcM1000P901a |
Screw |
Standard Part (works with P901) |
zcM1500 Parts List
zcM1500 Parts List
zcM1500-Specific Parts
Part # | Description |
ZCM1500P131 | magnetic bracket |
ZCM1500P136W | upper feed roller for 1500W |
ZCM1500P154W | pressure roller for 1500W |
ZCM1500P516 | pressure roller spring |
ZCM1500P517 | pressure roller holder |
ZCM1500P533 | roller unit |
zcM Series Parts
Part # |
Part Name |
Note |
zcM1000P101 |
Body cover |
Standard Part |
zcM1000P102 |
Panel cover |
Standard Part |
zcM1000P105 |
LED cover |
Standard Part |
zcM1000P106 |
Pressure Knob |
Standard Part |
zcM1000P107B |
Core holder |
Standard Part (1" / 35mm / 3") |
zcM1000P111 |
Transformer 117V |
Standard Part (on 117 V Machines) |
zcM1000P112 |
Transformer 230V(CE) |
Standard Part (on 230 V Machines) |
zcM1000P113 |
Screw (4* 8) |
Standard Part (To hold transformer on base) |
zcM1000P114 |
Nut with washer |
Standard Part (4mm) |
zcM1000P115 |
Base |
Standard Part |
zcM1000P116 |
Rubber feet |
Standard Part |
zcM1000P118 |
Power switch |
Standard Part |
zcM1000P120 |
Fuse (1A) |
Standard Part |
zcM1000P121 |
Fuse holder |
Standard Part |
zcM1000P124 |
Center frame |
Standard Part |
zcM1000P136 |
Separating roller unit |
Standard Part (Used with P138) |
zcM1000P138 |
Separating roller ring |
Standard Part |
zcM1000P141 |
Roller shaft |
Standard Part |
zcM1000P142 |
Screw (3*20) |
Standard Part (To Mount to P136) |
zcM1000P146 |
Bearing |
Standard Part |
zcM1000P150 |
Screw (3*25) |
Standard Part (To Mount feed roller) |
zcM1000P154PP5 |
Pressure roller 5T |
Standard Part (5 teeth for less pressure) |
zcM1000P155 |
Pressure roller collar |
Standard Part |
zcM1000P161 |
Cutter holder spring |
Standard Part |
zcM1000P164 |
Pressure roller spring |
Standard Part |
zcM1000P178 |
Earth spring |
Standard Part |
zcM1000P182 |
Flat rivet |
Standard Part |
zcM1000P187 |
Cutter motor (Yellow & Blue line) |
Standard Part |
zcM1000P200-1 |
Connector 4 (3 pins) |
Standard Part |
zcM1000P204 |
Pinion gear |
Standard Part |
zcM1000P206S |
Power cord (For 117V) |
Standard Part (USA, Plug type B) |
zcM1000P206-2 |
Power cord (For 230V) |
Standard Part (Schuko/EU, Plug type F) |
zcM1000P215 |
Sensor unit cover |
Standard Part |
zcM1000P228 |
Screw (3*8) |
Standard Part (To mount front holder) |
zcM1000P229 |
Screw (3*14) |
Standard Part (To mount control panel) |
zcM1000P230 |
Screw (2.6*3) |
Standard Part (To mount motor, Gold color) |
zcM1000P231 |
Screw (3*10A) |
Standard Part (To mount cutter gear cover) |
zcM1000P232 |
Screw (3*5) |
Standard Part (To mount cutter spring) |
zcM1000P233 |
Screw (3*8) |
Standard Part (To mount body) |
zcM1000P234 |
Screw (3*8) |
Standard Part (To ground earth) |
zcM1000P237 |
Screw (4*6) |
Standard Part (To mount gear unit) |
zcM1000P245 |
Advance / Cut button |
Standard Part |
zcM1000P246 |
"cm" Button |
Standard Part |
zcM1000P247 |
"mm" Button |
Standard Part |
zcM1000P248 |
"Cut" Button |
Standard Part |
zcM1000P249 |
"Advance" Button |
Standard Part |
zcM1000P250 |
"20" Button reset |
Standard Part |
zcM1000P251 |
"Reverse" Button |
Standard Part |
zcM1000P254/5 |
Blade set (Upper & Lower) |
Standard Part (Special coated blades) |
Standard Part (Special coated blades) |
||
zcM1000P256 |
Top Blade Holder |
Standard Part |
zcM1000P257PP |
Blade spring with comb |
Standard Part |
zcM1000P258 |
Blade liner (Right) |
Standard Part |
zcM1000P259 |
Blade liner (Left) |
Standard Part |
zcM1000P289 |
Silicone oil |
Included with all models |
zcM1000P312 |
Feed roller 2 |
Standard Part |
zcM1000P403 |
Flat gear 15 |
Standard Part |
zcM1000P404 |
Flat gear 16 |
Standard Part |
zcM1000P406 |
Flat gear shaft 14 |
Standard Part |
zcM1000P407 |
Flat gear shaft 13 |
Standard Part |
zcM1000P408 |
Collar 2 |
Standard Part |
zcM1000P418 |
Gear unit |
Standard Part |
zcM1000P421 |
Flat Gear 11 |
Standard Part |
zcM1000P422 |
Flat Gear 12 |
Standard Part |
zcM1000P423 |
Flat Gear 13 |
Standard Part |
zcM1000P424 |
Flat Gear 14 |
Standard Part |
zcM1000P427 |
Feed roller gear 3 |
Standard Part |
zcM1000P428 |
Screw (4*8) |
Standard Part (to mount gear cover) |
zcM1000P430 |
Separating roller gear |
Standard Part |
zcM1000P431 |
Cutter gear 2 unit |
Standard Part |
zcM1000P433 |
Cutter part gear cover 2 unit |
Standard Part |
zcM1000P435 |
Feed motor (Red & Brown line) |
Standard Part |
zcM1000P501 |
Side frame (Left) |
Standard Part |
zcM1000P502 |
Side frame (Right) |
Standard Part |
zcM1000P503 |
Separating roller holder |
Standard Part |
zcM1000P504 |
PCB |
Standard Part |
zcM1000P507S |
Cutter holder |
Standard Part (Plastic Frame Only with Front Holes) |
zcM1000P508S |
Cutter holder unit 2 |
Standard Part (Plastic frame + blades with front holes) |
zcM1000P517 |
Roller pressure unit 2 |
Standard Part |
zcM1000P518 |
Front holder unit 3 |
Standard Part (frame + motor) |
zcM1000P519 |
Front holder 3 |
Standard Part (Plastic frame only) |
zcM1000P520 |
Cut lever press 2 |
Standard Part |
zcM1000P521 |
Cut lever liner 2 |
Standard Part |
zcM1000P522 |
Cut lever collar |
Standard Part |
zcM1000P523 |
Cut lever unit 2 |
Standard Part |
zcM1000P524 |
Open spring |
Standard Part |
zcM1000P525 |
Open knob |
Standard Part |
zcM1000P526 |
Open set |
Standard Part |
zcM1000P528 |
Pinion gear unit 2 |
Standard Part |
zcM1000P533 |
Separating roller holder unit |
Standard Part (with P138 roller rings) |
zcM1000P550S |
Auto feed cutter unit |
Standard Part (with 3 flat pin connector) Complete Cutting Head |
zcM1000P555 |
Sensor cover |
(Plastic frame only) |
zcM1000P560-1 |
Sensor unit |
Standard Part (with 3 flat pin connector, frame + sensor) |
zcM1000P680 |
Safety guard (With 4 screws) |
Standard Accessory for 117V, Installed on 230V machines (Need P507-S) |
zcM1000P901 |
Stopper |
Standard Part (to secure cutting head) |
zcM1000P901a |
Screw |
Standard Part (works with P901) |
zcM2000 Parts List
zcM2000 Parts List
zcM2000-Specific Parts
Part # | Description |
ZCM2000P504-10 | 5mm cut PCB (D) |
ZCM2000P601 | main board unit 2 |
ZCM2000P601-10 | 10 memory PCB |
ZCM2000P605 | panel cover |
ZCM2000P612 | switch button 3 -Memory |
zcM Series Parts
Part # |
Part Name |
Note |
zcM1000P101 |
Body cover |
Standard Part |
zcM1000P102 |
Panel cover |
Standard Part |
zcM1000P105 |
LED cover |
Standard Part |
zcM1000P106 |
Pressure Knob |
Standard Part |
zcM1000P107B |
Core holder |
Standard Part (1" / 35mm / 3") |
zcM1000P111 |
Transformer 117V |
Standard Part (on 117 V Machines) |
zcM1000P112 |
Transformer 230V(CE) |
Standard Part (on 230 V Machines) |
zcM1000P113 |
Screw (4* 8) |
Standard Part (To hold transformer on base) |
zcM1000P114 |
Nut with washer |
Standard Part (4mm) |
zcM1000P115 |
Base |
Standard Part |
zcM1000P116 |
Rubber feet |
Standard Part |
zcM1000P118 |
Power switch |
Standard Part |
zcM1000P120 |
Fuse (1A) |
Standard Part |
zcM1000P121 |
Fuse holder |
Standard Part |
zcM1000P124 |
Center frame |
Standard Part |
zcM1000P136 |
Separating roller unit |
Standard Part (Used with P138) |
zcM1000P138 |
Separating roller ring |
Standard Part |
zcM1000P141 |
Roller shaft |
Standard Part |
zcM1000P142 |
Screw (3*20) |
Standard Part (To Mount to P136) |
zcM1000P146 |
Bearing |
Standard Part |
zcM1000P150 |
Screw (3*25) |
Standard Part (To Mount feed roller) |
zcM1000P154PP5 |
Pressure roller 5T |
Standard Part (5 teeth for less pressure) |
zcM1000P155 |
Pressure roller collar |
Standard Part |
zcM1000P161 |
Cutter holder spring |
Standard Part |
zcM1000P164 |
Pressure roller spring |
Standard Part |
zcM1000P178 |
Earth spring |
Standard Part |
zcM1000P182 |
Flat rivet |
Standard Part |
zcM1000P187 |
Cutter motor (Yellow & Blue line) |
Standard Part |
zcM1000P200-1 |
Connector 4 (3 pins) |
Standard Part |
zcM1000P204 |
Pinion gear |
Standard Part |
zcM1000P206S |
Power cord (For 117V) |
Standard Part (USA, Plug type B) |
zcM1000P206-2 |
Power cord (For 230V) |
Standard Part (Schuko/EU, Plug type F) |
zcM1000P215 |
Sensor unit cover |
Standard Part |
zcM1000P228 |
Screw (3*8) |
Standard Part (To mount front holder) |
zcM1000P229 |
Screw (3*14) |
Standard Part (To mount control panel) |
zcM1000P230 |
Screw (2.6*3) |
Standard Part (To mount motor, Gold color) |
zcM1000P231 |
Screw (3*10A) |
Standard Part (To mount cutter gear cover) |
zcM1000P232 |
Screw (3*5) |
Standard Part (To mount cutter spring) |
zcM1000P233 |
Screw (3*8) |
Standard Part (To mount body) |
zcM1000P234 |
Screw (3*8) |
Standard Part (To ground earth) |
zcM1000P237 |
Screw (4*6) |
Standard Part (To mount gear unit) |
zcM1000P245 |
Advance / Cut button |
Standard Part |
zcM1000P246 |
"cm" Button |
Standard Part |
zcM1000P247 |
"mm" Button |
Standard Part |
zcM1000P248 |
"Cut" Button |
Standard Part |
zcM1000P249 |
"Advance" Button |
Standard Part |
zcM1000P250 |
"20" Button reset |
Standard Part |
zcM1000P251 |
"Reverse" Button |
Standard Part |
zcM1000P254/5 |
Blade set (Upper & Lower) |
Standard Part (Special coated blades) |
Standard Part (Special coated blades) |
||
zcM1000P256 |
Top Blade Holder |
Standard Part |
zcM1000P257PP |
Blade spring with comb |
Standard Part |
zcM1000P258 |
Blade liner (Right) |
Standard Part |
zcM1000P259 |
Blade liner (Left) |
Standard Part |
zcM1000P289 |
Silicone oil |
Included with all models |
zcM1000P312 |
Feed roller 2 |
Standard Part |
zcM1000P403 |
Flat gear 15 |
Standard Part |
zcM1000P404 |
Flat gear 16 |
Standard Part |
zcM1000P406 |
Flat gear shaft 14 |
Standard Part |
zcM1000P407 |
Flat gear shaft 13 |
Standard Part |
zcM1000P408 |
Collar 2 |
Standard Part |
zcM1000P418 |
Gear unit |
Standard Part |
zcM1000P421 |
Flat Gear 11 |
Standard Part |
zcM1000P422 |
Flat Gear 12 |
Standard Part |
zcM1000P423 |
Flat Gear 13 |
Standard Part |
zcM1000P424 |
Flat Gear 14 |
Standard Part |
zcM1000P427 |
Feed roller gear 3 |
Standard Part |
zcM1000P428 |
Screw (4*8) |
Standard Part (to mount gear cover) |
zcM1000P430 |
Separating roller gear |
Standard Part |
zcM1000P431 |
Cutter gear 2 unit |
Standard Part |
zcM1000P433 |
Cutter part gear cover 2 unit |
Standard Part |
zcM1000P435 |
Feed motor (Red & Brown line) |
Standard Part |
zcM1000P501 |
Side frame (Left) |
Standard Part |
zcM1000P502 |
Side frame (Right) |
Standard Part |
zcM1000P503 |
Separating roller holder |
Standard Part |
zcM1000P504 |
PCB |
Standard Part |
zcM1000P507S |
Cutter holder |
Standard Part (Plastic Frame Only with Front Holes) |
zcM1000P508S |
Cutter holder unit 2 |
Standard Part (Plastic frame + blades with front holes) |
zcM1000P517 |
Roller pressure unit 2 |
Standard Part |
zcM1000P518 |
Front holder unit 3 |
Standard Part (frame + motor) |
zcM1000P519 |
Front holder 3 |
Standard Part (Plastic frame only) |
zcM1000P520 |
Cut lever press 2 |
Standard Part |
zcM1000P521 |
Cut lever liner 2 |
Standard Part |
zcM1000P522 |
Cut lever collar |
Standard Part |
zcM1000P523 |
Cut lever unit 2 |
Standard Part |
zcM1000P524 |
Open spring |
Standard Part |
zcM1000P525 |
Open knob |
Standard Part |
zcM1000P526 |
Open set |
Standard Part |
zcM1000P528 |
Pinion gear unit 2 |
Standard Part |
zcM1000P533 |
Separating roller holder unit |
Standard Part (with P138 roller rings) |
zcM1000P550S |
Auto feed cutter unit |
Standard Part (with 3 flat pin connector) Complete Cutting Head |
zcM1000P555 |
Sensor cover |
(Plastic frame only) |
zcM1000P560-1 |
Sensor unit |
Standard Part (with 3 flat pin connector, frame + sensor) |
zcM1000P680 |
Safety guard (With 4 screws) |
Standard Accessory for 117V, Installed on 230V machines (Need P507-S) |
zcM1000P901 |
Stopper |
Standard Part (to secure cutting head) |
zcM1000P901a |
Screw |
Standard Part (works with P901) |
zcM1100 Parts List
zcM1100 Parts List
zcM1100-Specific Parts
Part # |
Part Name |
Note |
zcM1100P101 |
Body cover |
Standard Part (for zcM1100) |
zcM1100P102 |
L.E.D. Cover |
Standard Part (for zcM1100) |
zcM1100P103 |
Pressure knob |
Standard Part (for zcM1100) |
zcM1100P105 |
Screw (B3*6) (For L.E.D. Cover) |
Standard Part (for zcM1100) |
zcM1100P401 |
Front holder (Plastic frame only) |
Standard Part (for zcM1100) |
zcM1100P403 |
Front connector |
Standard Part (for zcM1100) |
zcM1100P411 |
Flat gear shaft 21 |
Standard Part (for zcM1100) |
zcM1100P412 |
Flat gear shaft 22 |
Standard Part (for zcM1100) |
zcM1100P450 |
Front holder unit |
Standard Part (for zcM1100) |
zcM1100P501 |
"Auto" button (Advance / Cut) |
Standard Part (for zcM1100) |
zcM1100P502 |
Button 1 |
Standard Part (for zcM1100) |
zcM1100P503 |
Button 2 |
Standard Part (for zcM1100) |
zcM1100P504 |
Button 3 |
Standard Part (for zcM1100) |
zcM1100P505 |
Button 4 |
Standard Part (for zcM1100) |
zcM1100P506 |
Button 5 |
Standard Part (for zcM1100) |
zcM1100P507 |
Button 6 |
Standard Part (for zcM1100) |
zcM1100P550-1 |
PCB |
Standard Part (for zcM1100) |
zcM1100P601 |
Cutter holder |
Standard Part (for zcM1100, Plastic frame only) |
zcM1100P602 |
Sensor cover |
Standard Part (for zcM1100, Plastic frame only) |
zcM1100P604 |
Connector lid |
Standard Part (for zcM1100) |
zcM1100P606 |
Sensor unit cover |
Standard Part (for zcM1100) |
zcM1100P608 |
Connector 2 |
Standard Part (for zcM1100) |
zcM1100P611-1 |
Shutter 2 |
Standard Part (for zcM1100) |
zcM1100P612-1 |
Slider 2 |
Standard Part (for zcM1100) |
zcM1100P613-1 |
Stopper 2 |
Standard Part (for zcM1100) |
zcM1100P614 |
Remover |
Standard Part (for zcM1100) |
zcM1100P615 |
Placket |
Standard Part (for zcM1100) |
zcM1100P616-1 |
Mover 2 |
Standard Part (for zcM1100) |
zcM1100P617 |
Stopper shaft |
Standard Part (for zcM1100) |
zcM1100P618 |
Shutter spring |
Standard Part (for zcM1100) |
zcM1100P619 |
Return spring |
Standard Part (for zcM1100) |
zcM1100P621 |
Blade spring |
Standard Part (for zcM1100) |
zcM1100P621PP |
Blade spring (with comb) |
Optional Part (for zcM1100) |
zcM1100P630 |
Screw (3*8) (To mount placket) |
Standard Part (for zcM1100) |
zcM1100P631 |
Screw (B2*10) (To mount switch) |
Standard Part (for zcM1100) To mount switch |
zcM1100P632 |
Screw (M2.6*3) (For fix solenoid) |
Standard Part (for zcM1100) To mount solenoid |
zcM1100P633 |
E-ring |
Standard Part (for zcM1100) |
zcM1100P634 |
O-ring |
Standard Part (for zcM1100) |
zcM1100P652 |
Sensor unit |
Standard Part (for zcM1100) |
zcM1100P653 |
Solenoid unit |
Standard Part (for zcM1100) |
zcM1100P654 |
Cutter holder unit |
Standard Part (for zcM1100, Without sensor unit) |
zcM1100P656 |
Auto feed cutter unit (MA-1100) |
Standard Part (for zcM1100) |
zcM Series Parts
Part # |
Part Name |
Note |
zcM1000P101 |
Body cover |
Standard Part |
zcM1000P102 |
Panel cover |
Standard Part |
zcM1000P105 |
LED cover |
Standard Part |
zcM1000P106 |
Pressure Knob |
Standard Part |
zcM1000P107B |
Core holder |
Standard Part (1" / 35mm / 3") |
zcM1000P111 |
Transformer 117V |
Standard Part (on 117 V Machines) |
zcM1000P112 |
Transformer 230V(CE) |
Standard Part (on 230 V Machines) |
zcM1000P113 |
Screw (4* 8) |
Standard Part (To hold transformer on base) |
zcM1000P114 |
Nut with washer |
Standard Part (4mm) |
zcM1000P115 |
Base |
Standard Part |
zcM1000P116 |
Rubber feet |
Standard Part |
zcM1000P118 |
Power switch |
Standard Part |
zcM1000P120 |
Fuse (1A) |
Standard Part |
zcM1000P121 |
Fuse holder |
Standard Part |
zcM1000P124 |
Center frame |
Standard Part |
zcM1000P136 |
Separating roller unit |
Standard Part (Used with P138) |
zcM1000P138 |
Separating roller ring |
Standard Part |
zcM1000P141 |
Roller shaft |
Standard Part |
zcM1000P142 |
Screw (3*20) |
Standard Part (To Mount to P136) |
zcM1000P146 |
Bearing |
Standard Part |
zcM1000P150 |
Screw (3*25) |
Standard Part (To Mount feed roller) |
zcM1000P154PP5 |
Pressure roller 5T |
Standard Part (5 teeth for less pressure) |
zcM1000P155 |
Pressure roller collar |
Standard Part |
zcM1000P161 |
Cutter holder spring |
Standard Part |
zcM1000P164 |
Pressure roller spring |
Standard Part |
zcM1000P178 |
Earth spring |
Standard Part |
zcM1000P182 |
Flat rivet |
Standard Part |
zcM1000P187 |
Cutter motor (Yellow & Blue line) |
Standard Part |
zcM1000P200-1 |
Connector 4 (3 pins) |
Standard Part |
zcM1000P204 |
Pinion gear |
Standard Part |
zcM1000P206S |
Power cord (For 117V) |
Standard Part (USA, Plug type B) |
zcM1000P206-2 |
Power cord (For 230V) |
Standard Part (Schuko/EU, Plug type F) |
zcM1000P215 |
Sensor unit cover |
Standard Part |
zcM1000P228 |
Screw (3*8) |
Standard Part (To mount front holder) |
zcM1000P229 |
Screw (3*14) |
Standard Part (To mount control panel) |
zcM1000P230 |
Screw (2.6*3) |
Standard Part (To mount motor, Gold color) |
zcM1000P231 |
Screw (3*10A) |
Standard Part (To mount cutter gear cover) |
zcM1000P232 |
Screw (3*5) |
Standard Part (To mount cutter spring) |
zcM1000P233 |
Screw (3*8) |
Standard Part (To mount body) |
zcM1000P234 |
Screw (3*8) |
Standard Part (To ground earth) |
zcM1000P237 |
Screw (4*6) |
Standard Part (To mount gear unit) |
zcM1000P245 |
Advance / Cut button |
Standard Part |
zcM1000P246 |
"cm" Button |
Standard Part |
zcM1000P247 |
"mm" Button |
Standard Part |
zcM1000P248 |
"Cut" Button |
Standard Part |
zcM1000P249 |
"Advance" Button |
Standard Part |
zcM1000P250 |
"20" Button reset |
Standard Part |
zcM1000P251 |
"Reverse" Button |
Standard Part |
zcM1000P254/5 |
Blade set (Upper & Lower) |
Standard Part (Special coated blades) |
Standard Part (Special coated blades) |
||
zcM1000P256 |
Top Blade Holder |
Standard Part |
zcM1000P257PP |
Blade spring with comb |
Standard Part |
zcM1000P258 |
Blade liner (Right) |
Standard Part |
zcM1000P259 |
Blade liner (Left) |
Standard Part |
zcM1000P289 |
Silicone oil |
Included with all models |
zcM1000P312 |
Feed roller 2 |
Standard Part |
zcM1000P403 |
Flat gear 15 |
Standard Part |
zcM1000P404 |
Flat gear 16 |
Standard Part |
zcM1000P406 |
Flat gear shaft 14 |
Standard Part |
zcM1000P407 |
Flat gear shaft 13 |
Standard Part |
zcM1000P408 |
Collar 2 |
Standard Part |
zcM1000P418 |
Gear unit |
Standard Part |
zcM1000P421 |
Flat Gear 11 |
Standard Part |
zcM1000P422 |
Flat Gear 12 |
Standard Part |
zcM1000P423 |
Flat Gear 13 |
Standard Part |
zcM1000P424 |
Flat Gear 14 |
Standard Part |
zcM1000P427 |
Feed roller gear 3 |
Standard Part |
zcM1000P428 |
Screw (4*8) |
Standard Part (to mount gear cover) |
zcM1000P430 |
Separating roller gear |
Standard Part |
zcM1000P431 |
Cutter gear 2 unit |
Standard Part |
zcM1000P433 |
Cutter part gear cover 2 unit |
Standard Part |
zcM1000P435 |
Feed motor (Red & Brown line) |
Standard Part |
zcM1000P501 |
Side frame (Left) |
Standard Part |
zcM1000P502 |
Side frame (Right) |
Standard Part |
zcM1000P503 |
Separating roller holder |
Standard Part |
zcM1000P504 |
PCB |
Standard Part |
zcM1000P507S |
Cutter holder |
Standard Part (Plastic Frame Only with Front Holes) |
zcM1000P508S |
Cutter holder unit 2 |
Standard Part (Plastic frame + blades with front holes) |
zcM1000P517 |
Roller pressure unit 2 |
Standard Part |
zcM1000P518 |
Front holder unit 3 |
Standard Part (frame + motor) |
zcM1000P519 |
Front holder 3 |
Standard Part (Plastic frame only) |
zcM1000P520 |
Cut lever press 2 |
Standard Part |
zcM1000P521 |
Cut lever liner 2 |
Standard Part |
zcM1000P522 |
Cut lever collar |
Standard Part |
zcM1000P523 |
Cut lever unit 2 |
Standard Part |
zcM1000P524 |
Open spring |
Standard Part |
zcM1000P525 |
Open knob |
Standard Part |
zcM1000P526 |
Open set |
Standard Part |
zcM1000P528 |
Pinion gear unit 2 |
Standard Part |
zcM1000P533 |
Separating roller holder unit |
Standard Part (with P138 roller rings) |
zcM1000P550S |
Auto feed cutter unit |
Standard Part (with 3 flat pin connector) Complete Cutting Head |
zcM1000P555 |
Sensor cover |
(Plastic frame only) |
zcM1000P560-1 |
Sensor unit |
Standard Part (with 3 flat pin connector, frame + sensor) |
zcM1000P680 |
Safety guard (With 4 screws) |
Standard Accessory for 117V, Installed on 230V machines (Need P507-S) |
zcM1000P901 |
Stopper |
Standard Part (to secure cutting head) |
zcM1000P901a |
Screw |
Standard Part (works with P901) |